Archive for March 2014

Type 65 Coupe Update: Fuel Pump Bracket, Cable Bulkhead Brackets, E-Brake Location   Leave a comment

After something like three or four false starts, I finally settled on a way to mount the external fuel pump on my Coupe. The final solution is so simple, I feel stupid….

First, I tried mounting the pump on the lower brace, under the IRS pumpkin. But that just did not look right, and it was difficult to access from either above or below the car. Then I tried mounting the pump on the Factory Five Metal battery box, but discovered the battery box blocks access to the fill and drain plugs on the differential.

Here is the final answer, a simple, flat plate of 1/8-inch aluminum. This will help simplify the fuel hose routing, too.

IMG_8357-kh6wz - simple fuel pump bracket

More Fabrication

I made a pair of triangular plates to create a bulkhead to hold the e-brake cable and the fuel hoses (one for supply to the engine and one for the return into the tank) on the passenger side of the chassis. An identical plate for the driver side will be used for the other e-brake cable and any wiring harness going to the rear of the car.

Since the 1/8-inch aluminum plate I am using for these brackets is scrap material, some extra holes are sometimes included in the items I make. When I am not able to re-use existing holes, I patch them with JB Weld or epoxy, then paint the item with high temperature BBQ paint. These brackets are finished in silver.

IMG_8387-kh6wz - triangle bracket 1

 

IMG_8400 - kh6wz - triangle bracket 2

The large holes are cushioned with a PCV grommet; it is thick and large enough to pass the 3/8-inch fuel lines nicely.

Here are some views of the passenger-side bracket installed with Clecos:

IMG_8404 kh6wz - triangle bracket installed - P-side

 

 

 

IMG_8406 - kh6wz - triangle bracket - fuel line

Next, I started laying out the e-brake cables and the complete kit e-brake handle. When I installed the rear brakes, I thought the cables looked too short. And last night I noticed that I am correct – the cables supplied with the IRS brake kit are about four to six inches too short.

I may have a solution to this, based on some Forum postings on this same topic — see the photo below. I do not like the turn buckle from the hardware store, I think I should replace it with a stainless steel clevis six to eight inches long to allow for adjustment. (McMaster-Carr items. . . )

IMG_8370 - kh6wz - e-brake assy1

UPDATE: I ordered an e-brake kit from Richard Oben of North Race Cars. (The same place I ordered my air conditioner – yet to be installed). The kit will move the e-brake to a more practical location at the top of the transmission tunnel.

Many builders of the Roadster as well as the Coupe do not like the way the brake cables rub against the big four inch tube. I will make a small Teflon block and mount it to the bottom of the chassis so the cable can slide more easily, and make it look much nicer. More details when I get to that step.

Main Wire Harness
I started laying out the main wire harness. A few weeks ago, I painted the fuse panel with white appliance epoxy paint. This will brighten up the underside of the dash and will prevent corrosion. Based on something I read on the Roadster section of one of the F5R Forums, I added a small hinge to the fuse panel mounting plate. You can see the hinge on the right side of the bracket in this picture:

 

IMG_8408 - kh6wz - fuse panel painted

 

However, this is bad advice, at least for my Coupe application. This is not a good thing to do for several reasons:

1) It moves the fuse block about a quarter-inch forward into the footbox, and adds strain to several wires in the Ron Francis harness supplied with the Complete Kit.

2) The reason for the hinge was to make it possible to swing the entire panel down for easy servicing. However, this is impossible, since there is not enough slack and the thick harness will not allow the fuse panel to simply “swing down.”

3) The mounting holes must be very close to the edge of the 2-inch rail. Removing the hinge makes a better location for the mounting screws.

After removing the hinge, and mounting the fuse panel per the instructions, I noticed some “squishiness” in the fuse panel, which I do not like. I have not seen this mentioned in any post so I thought I would bring it up here.

The fuse panel is a piece of thin aluminum, laser cut to shape to hold the plastic fuse panel. Three zip screws (the self-tapping hex-head screws that held the cockpit aluminum in place when the kit was shipped) fasten it in place under the driver footbox, near the steering column.

All fine and dandy, but the fourth corner is “floating in space” and flexes easily. I decided to add a small aluminum bracket to make the fuse panel stronger (flex less). I hope the bracket does not get in the way of anything to be mounted later….

 

IMG_8422 - kh6wz - added bracket for fuse panel

Advertisements

Great Sign at the Lumber Store – Never Lie   Leave a comment

Saw this and had to share it. .. 

kh6wz - x-ray sign Ganahl Lumber

Flash Back from the Big Green Egg   Leave a comment

I had to perform a “sterilization” operation on my BGE this morning. Because of the recent rain and lack of use, I noticed some mold growing inside my ceramic cooker. This is not un-common, and usually happens in humid climates. The solution is to simply make a very hot fire to burn off and sterilize the cooking area.

I made a screaming hot fire, over 500 to 550 degrees F.

Since I wanted to cook a pair of tri-tip roasts later in the day, I wanted to snuff the fire and let it cool down so I could use it later. So, I closed the top and bottom vents, and let the fire starve for several minutes.

When it reached around 250 or 300 degrees (4 or 6 hours later), I “burped” the lid three times (my normal procedure to prevent flash-back), and opened the lid to see if the heat burned and killed off the inside surfaces. About two seconds after I lifted the lid, I heard that scary “whoooooosh” sound of the fire coming back to life. This was the biggest and loudest flash-back I have ever survived.

Here’s a picture of my “lifting arm” —

IMG_8395 - kh6wz - BGE singed arm hair

 

I was lucky – No burns to my skin, just some very singed arm-hair.

 

Meanwhile, the two tri-tip roasts came out perfect – Those will make great sandwiches for the next few weeks….